$194.99 $199.99
In stock 30 Products
If you are pulling cable between floors in a commercial building or multi-unit residence, this Wavenet Cat6 riser cable gives you the bandwidth and code compliance you need without paying for plenum-grade materials you do not require. It is rated for 600MHz on an unshielded twisted pair design built around 23 AWG solid bare copper conductors, so signal quality stays strong and consistent across the full thousand-foot run. The CMR and FT4 certifications satisfy inspectors in vertical shafts, while the Reelex II packaging on part number 6E04URXX4N feeds smoothly and resists tangles during long pulls. A separator inside the jacket keeps pair geometry consistent, the ripcord makes stripping fast and clean, and the flame-retardant PVC outer shell is tested to retain tensile strength even after high-temperature aging. Whether you are wiring IP cameras, wireless access points, VoIP phones, or standard Gigabit drops, this TIA-568-C.2 verified, RoHS-compliant spool covers the distance without complicating your install.
$409.99
In stock 30 Products
The Wavenet H16E164MYL2-500 is a dual-cable combination that pairs a CAT6E 600MHz UTP network cable with a 16AWG 4-conductor audio cable on a single 500-foot RIB, making it a go-to choice for any AV or structured wiring installation that needs both data and speaker runs in the same pathway. The CAT6E side uses 23AWG bare solid copper conductors with HDPE insulation and a flame-retardant PVC jacket, rated through 600MHz for reliable Gigabit Ethernet performance. The 16AWG audio cable features four twisted copper conductors — color-coded Red, White, Yellow, and Blue — with a polyethylene/polypropylene insulation, a PVC jacket, and a 300V operating rating across a -20°C to +60°C temperature range. Both cables carry CMR and FT4 ratings for riser and in-wall use, and the assembly is ETL Listed under c(ETL)US. Packaged in a yellow-jacketed 500ft RIB for clean, tangle-free feeding on the job site.
$219.99 $239.99
In stock 30 Products
The Wavenet H16E16QMBL2-500 combines a CAT6E 600MHz UTP cable and an RG-6 Quad Shield Coaxial Cable on a single 500-foot reel, making it a practical choice for any installation that needs both data and video in the same run. The CAT6E side uses 23AWG bare solid copper conductors with HDPE insulation and a flame-retardant PVC jacket, delivering reliable network performance through 600MHz. The RG-6 Quad Shield coaxial cable features a copper-covered steel center conductor, foam PE dielectric, dual bonded foil and dual Al-Mag braid shielding, a 75-ohm impedance, and a CMR/CL2-rated jacket — with factory sweep testing confirmed to 3.0GHz. Both cables carry a CMR rating for in-wall and riser use, and the assembly is ETL Listed for North American compliance. Sold as a 500ft reel in a blue jacket, part number H16E16QMBL2-500, this Wavenet combo cable saves time and conduit space on any structured wiring job.
$524.99 $609.99
In stock 20 Products
The Wavenet H26E26QMGN2-500 is a 500-foot reel combination cable that integrates two 23AWG CAT6E 600MHz UTP data cables and two 18AWG RG-6 Quad Shield coaxial cables into a single, green-jacketed assembly — letting installers deliver Gigabit Ethernet and broadband video to the same outlet location in a single wall pull. The CAT6E cables comply with TIA/EIA-568-C.2 and are ETL listed as CMR, supporting 1000BASE-T Gigabit Ethernet, Fast Ethernet, and ATM 155 Mbps applications. The quad-shielded RG-6 cables use a four-layer aluminum foil and braid construction, providing strong RF isolation and CATV performance swept and verified to 3.0GHz. Both cable types are RoHS compliant, CMR riser rated for vertical runs, and verified to C(ETL)US. Whether you're wiring a new home, an MDU building, or a hospitality property, this combination cable streamlines structured wiring while meeting the certification requirements of modern residential and commercial installations.
$1,149.99 $1,244.99
In stock 30 Products
The Wavenet RG11PWH2 is a 14AWG RG-11U Plenum-rated (CMP) broadband coaxial cable built for professional CATV and signal distribution installations where fire code compliance is required. It features a Copper-Clad Steel center conductor surrounded by FEP dielectric insulation, a dual-shield system consisting of an aluminum/poly tape foil and a 60% aluminum braid, and a Plenum PVC outer jacket in white. Rated for 75 Ohm impedance with a velocity of propagation of 84%, this cable handles frequencies swept and tested to 3.0 GHz, with attenuation as low as 0.09 dB/100m at 1 MHz and 9.88 dB/100m at 3000 MHz. Compliant with UL 1655, UL 13, UL 444, SCTE IPS-SP-001, and ROHS, it's UL listed and NEC-rated for safe installation in air-handling plenum spaces. Available in a 1000-foot reel at a nominal weight of 63 lbs.
$224.99 $254.99
In stock 30 Products
The Wavenet RG11QRBK2 is a 14AWG RG-11U Quad Shield Riser-rated (CMR) broadband coaxial cable engineered for vertical in-building signal distribution where strong shielding and low signal loss are essential. It's built around a Copper-Clad Steel center conductor insulated with foam polyethylene, wrapped in a quad-shield system of aluminum foil and 60% aluminum braid, and finished with a black PVC CMR-rated jacket. Electrically, the cable holds a 75 Ohm impedance with a velocity of propagation of 82% and a capacitance of 15.5 pF/ft, with attenuation measured from 1.50 dB/100m at 5 MHz through 25.60 dB/100m at 3000 MHz swept and ETL-verified to 3.0 GHz. Compliant with SCTE, UL 444, and ROHS, and ETL Listed through Intertek, it's packaged on a 1000-foot reel weighing 64 lbs., ready for professional CATV and broadband riser installations.
$185.99
In stock 30 Products
The Wavenet RG11RBK2 is a 14 AWG RG-11U 60% Shield Riser (CMR) Broadband Coaxial Cable supplied on a 1000-foot black reel, purpose-built for CATV distribution runs where low signal attenuation over long distances matters most. Its solid Copper Clad Steel center conductor noticeably larger than what you'd find in standard RG-6 delivers a DC resistance of just 12.7 ohms per 1000 feet and keeps attenuation to 15.08 dB/100m at 1 GHz and 26.89 dB/100m at 3.0 GHz, making it a go-to for trunk and backbone wiring in apartment buildings, hotels, and commercial CATV systems. Foam Polyethylene insulation, a bonded aluminum tape layer, and a 60% aluminum braid shield work together to maintain signal integrity and reject interference. ETL listed by Intertek and compliant with SCTE IPS-SP-001, UL 1655, UL 13, UL 444, and ROHS, this cable meets riser-installation code requirements right out of the box.
$339.99 $369.99
In stock 30 Products
The Wavenet RG59PWH4 is a plenum-rated (CMP) RG-59/U coaxial cable built for installations in air-handling spaces where fire and smoke safety codes apply. It runs a solid bare copper center conductor at 20 AWG, wrapped in Foam FEP insulation and shielded with a dual-layer system — foil plus a 95% C.C.A. braid — that keeps signal clean from 1 MHz all the way to 3,000 MHz. Electrical characteristics are tight: 75-ohm impedance, 16 pF/ft capacitance, 84% velocity of propagation, and conductor DCR of just 10.5 ohms per 1000 feet. UL verified and compliant with NEC Article 800, it satisfies the certification requirements that commercial and institutional plenum installations demand. The plenum polymer jacket meets the reduced flame and smoke standards that CMP rating requires, and the white finish keeps things clean above the ceiling. Comes packed in a 1000ft Reelex II spool, RoHS compliant, and ready for the job site.
$154.99
In stock 30 Products
The Wavenet RG-59/U 95% CMR Coaxial Cable (RG59RXX4) is a riser-rated, 75-ohm signal cable built around a solid bare copper center conductor at 20 AWG a reliable foundation for CCTV, security, and analog video distribution in commercial and residential buildings. Wrapped in Foam PE insulation and shielded with a 95% C.C.A. braid, it delivers consistent attenuation performance from 50 MHz all the way up to 2,200 MHz, with a velocity of propagation of 84% and capacitance of 15.5 pF/ft. The CMR (Riser) rating makes it code-appropriate for vertical in-wall routing between floors, while ETL listing and compliance with SCTE IPS-SP-001, UL 1655, and UL13 standards satisfies the certification requirements most professional installs demand. RoHS compliant and packed in a convenient 1000ft pull box, it's available in black or white PVC jackets rated for temperatures from -20 to 60°C and ready for the job site.
$119.99
In stock 30 Products
The Wavenet RG6OSPBK2 is a professional outdoor direct burial RG-6 coaxial cable built for reliable CATV, broadband, and satellite signal distribution across demanding installations. It features a solid 18 AWG copper-clad steel center conductor wrapped in a foam polyethylene dielectric, then shielded with a 60% aluminum braid before being jacketed in UV-stabilized polyethylene — keeping it durable whether mounted above ground or run directly underground. The cable maintains a consistent 75-ohm impedance and a velocity of propagation of 84%, having been swept and certified to 3.0 GHz for compatibility with current and next-generation broadband frequencies. Signal attenuation runs from just 2.66 dB/100m at 5 MHz up to 37.88 dB/100m at 3,000 MHz. Rated for temperatures from –20°C to +60°C and RoHS compliant, it meets SCTE IPS-SP-001, UL 1655, UL 13, and UL 444 standards. This ETL-listed cable ships on a convenient 1,000-foot reel in black, making it ideal for large-scale residential or commercial cable installations.
$129.99 $149.99
In stock 30 Products
The Wavenet RG6QOSPBK2 is a 1,000-foot RG-6 quad shield coaxial cable built specifically for outdoor and direct burial applications where durability and signal integrity over distance are essential. At its core is a solid 18 AWG Copper Clad Steel conductor wrapped in Foam PE dielectric, delivering a 75-ohm impedance system with 84% velocity of propagation and a DC resistance of 28.6 ohms per 1,000 feet. A dual-layer aluminum braid shield — 60% on the inner braid, 40% on the outer — provides robust interference rejection across a frequency range swept and verified to 3.0 GHz. The Polyethylene jacket is UV rated and moisture resistant, making it equally suitable for aerial runs, conduit burial, and direct underground installation. Certified to UL 1655, UL 13, UL 444, and SCTE IPS-SP-001 with c(ETL)US listing and full RoHS compliance, this cable meets the performance and safety standards outdoor CATV and broadband installations demand. Available in black on a 1,000-foot reel.
$424.99
In stock 30 Products
The Wavenet RG6QPWH4 is a 1,000-foot RG-6 quad shield plenum coaxial cable built for CATV and broadband signal distribution in above-ceiling air-handling spaces where NEC Article 800 requires CMP-rated cabling. At its core is a solid 18 AWG Copper Clad Steel conductor insulated with Foam FEP — a fluoropolymer dielectric chosen for its low-smoke, low-flame-spread properties — delivering a 75-ohm system with 84% velocity of propagation. The quad-shield assembly uses a foil-plus-braid approach on both the inner and outer layers: an Aluminum/Poly Tape foil paired with a 60% aluminum braid inside, and a second foil paired with a 40% aluminum braid outside, providing robust interference rejection across a frequency range swept and verified to 3.0 GHz. The Plenum Polymer jacket and FT6 rating satisfy both U.S. and Canadian plenum requirements. Holding a c(UL)US listing and full RoHS compliance, it ships in white on a tangle-free 1,000-foot Reelex II spool.
$454.99 $484.99
In stock 30 Products
The Wavenet RG6QPWH4-BC is a high-performance RG-6 quad shield plenum coaxial cable designed for demanding architectural installations. Featuring an 18 AWG solid bare copper conductor, this cable delivers exceptional clarity and minimal signal degradation for CATV networks. Its complex four-layer shielding system includes dual aluminum/poly tape shields alongside alternating 60% and 40% aluminum braids to maximize protection against electromagnetic interference. Engineered with a durable foamed FEP insulation and a white plenum polymer jacket, the cable safely complies with NEC Article 800 standards and is fully UL Verified for indoor air spaces. It offers a 75-Ohm impedance, a high velocity of propagation at 84%, and is swept up to 3.0 GHz to ensure elite broadband distribution. Packaged in a practical 1000-foot Reelex II box, this RoHS-compliant coaxial cable provides commercial installers with an efficient, reliable solution for clean signal transmission across extensive frequencies. This premium bulk cable maintains a nominal weight of 36 pounds per package.
Wavenet RG6QRWH2-500SM RG-6 Quad Shield DUAL SIAMESE (CCS) CMR 18AWG 3.0GHz 500ft Reel Coaxial Cable
$154.99 $179.99
In stock 30 Products
Wavenet RG6QRWH2-500SM RG-6 Quad Shield DUAL SIAMESE (CCS) CMR 18AWG 3.0GHz 500ft Reel Coaxial Cable
The Wavenet RG6QRWH2-500SM is a white, 500-foot reel of 18 AWG RG-6 Quad Shield Dual Siamese Coaxial Cable built for CATV installations that demand riser-rated (CMR) performance up to 3.0 GHz. Each of the two bonded coaxial elements features a solid Copper Clad Steel center conductor wrapped in Foam PE insulation, then shielded by two layers of aluminum braid — 60% and 40% coverage respectively — for strong protection against interference across the full frequency range. With 75-ohm impedance, a capacitance of 15.5 pF/ft, and an 84% velocity of propagation, the cable meets standard CATV system requirements and complies with SCTE IPS-SP-001, UL 1655, UL 13, UL 444, and RoHS. ETL listed by Intertek and operating between -20°C and 60°C, it is a reliable, code-compliant choice for multi-floor residential and commercial signal distribution where a dual coaxial run in one jacket simplifies the install.
$99.99
In stock 30 Products
The Wavenet RG6QRXX2 is a quad shield, riser-rated (CMR) RG-6 coaxial cable wound on a convenient 1000ft reel and built for CATV, satellite, and broadband distribution where both signal performance and code compliance are required. It runs a solid copper clad steel center conductor at 18 AWG, insulated with Foam PE and wrapped in four layers of aluminum shielding two foil layers and two braids at 60% and 40% coverage providing superior interference rejection compared to standard dual-shield designs. Electrical specs are solid throughout: 75-ohm impedance, 15.5 pF/ft capacitance, 84% velocity of propagation, and attenuation performance CATV swept and verified all the way to 3.0 GHz. The FR-PVC jacket carries the CMR riser rating required for vertical in-wall runs between floors, with ETL listing from Intertek confirming compliance with SCTE IPS-SP-001, UL 1655, UL 13, and UL 444 standards. Available in black or white, and RoHS compliant.
$99.99
In stock 30 Products
The Wavenet RG6QRXX3 is a 1,000-foot RG-6 quad shield coaxial cable delivered on a RIB (Reel In a Box) spool — a packaging format that keeps cable organized and tangle-free through long pulls on commercial and residential installations. Built around a solid 18 AWG Copper Clad Steel conductor insulated with Foam PE dielectric, it delivers a 75-ohm impedance system with a velocity of propagation of 84% and capacitance of 15.5 pF/ft. A dual-layer aluminum braid shield — 60% on the inner layer, 40% on the outer — provides strong interference rejection across a range swept and verified to 3.0 GHz. The FR-PVC jacket carries both a CMR riser rating and FT4 flame retardancy, making it code-compliant for floor-to-floor signal runs in multi-story buildings. Certified to UL 1655, UL 13, UL 444, and SCTE IPS-SP-001, with c(ETL)US listing and RoHS compliance, it is available in black or white.
$99.99
In stock 30 Products
The Wavenet RG6QRXX4 is a 1,000-foot RG-6 quad shield coaxial cable built for reliable CATV, satellite, and broadband signal distribution in riser-rated installations. At its core is a solid 18 AWG Copper Clad Steel conductor wrapped in Foam PE dielectric, delivering a 75-ohm impedance system with 84% velocity of propagation. A dual-layer aluminum braid shield — 60% coverage on the first layer, 40% on the second — provides strong interference rejection across a frequency range swept and verified to 3.0 GHz. The FR-PVC jacket carries a CMR riser rating along with FT4 flame retardancy, making it compliant for vertical runs between floors in commercial and multi-unit residential buildings. Certified to UL 1655, UL 13, UL 444, and SCTE IPS-SP-001 with c(ETL)US listing and full RoHS compliance, this cable meets the performance and safety benchmarks installers need. Available in black or white on a tangle-free REELEX II spool.
$74.99
In stock 29 Products
The Wavenet RG6QRXX4-500 brings the same quad-shield performance as the full 1,000-foot version into a more manageable 500-foot REELEX II spool — an 18-lb package that's easy to carry on a service call and feeds cable tangle-free through the tightest pulls. At its core is a solid 18 AWG Copper Clad Steel conductor surrounded by Foam PE dielectric, producing a 75-ohm impedance system with 84% velocity of propagation and 15.5 pF/ft capacitance. Two aluminum braid layers — 60% on the inner shield, 40% on the outer — deliver strong interference rejection across a frequency range swept and verified to 3.0 GHz. The FR-PVC jacket carries a CMR riser rating and FT4 flame retardancy, qualifying it for in-wall and floor-to-floor signal routing. Certified to UL 1655, UL 13, UL 444, and SCTE IPS-SP-001 with c(ETL)US listing and RoHS compliance, it's available in black or white.
$174.99
In stock 30 Products
The Wavenet RG6QRXX4-BC is a 1,000-foot RG-6 quad shield coaxial cable built around a solid 18 AWG Bare Copper conductor — a meaningful step up from Copper Clad Steel, delivering a DC resistance of just 6.8 Ω per 1,000 feet versus the 35.9 Ω typical of CCS alternatives. That lower resistance means less signal loss at the conductor level, which matters most on long-distance runs in CATV, satellite, and broadband distribution systems. The cable pairs its Bare Copper core with Foam PE dielectric and an aluminum braid shield, wrapped in a PVC jacket rated CMR for riser and in-wall installation. Performance is swept and verified to 3.0 GHz, with c(ETL)US listing and full RoHS compliance confirming both signal and regulatory benchmarks are met. Delivered on a tangle-free 1,000-foot REELEX II spool and certified to SCTE IPS-SP-001, UL 1655, UL 13, and UL 444, it is available in black or white.
$439.99 $494.99
In stock 30 Products
The Wavenet RG6UPWH4 is a 1,000-foot, plenum-rated (CMP) RG-6 coaxial cable built for reliable signal distribution in commercial and professional environments. It features an 18 AWG copper clad steel center conductor paired with a dual-shield system — aluminum foil plus a 60% aluminum braid — delivering consistent signal integrity up to 3.0 GHz with a standard 75 Ohm impedance. The white CMP jacket meets FT6 plenum fire-safety requirements, making it compliant for installation in air-handling spaces where building codes call for low-smoke cable. Sequential footage marking along the jacket keeps large installations organized, while the REELEX II box packaging ensures smooth, tangle-free payout on the job site. Certified c(ETL) Listed, compliant with TIA-568-C.2 and UL444, and RoHS compliant, this cable is a solid choice for broadband, CATV, satellite, CCTV, and general video wiring projects that demand certified plenum performance without sacrificing signal quality.
